7Axis Industrial Client area

Workshop practice

Seeing what the paper hides

In an RFID ticket, the chip and antenna are hidden between two layers of paper. From the outside, you cannot see whether they are correctly positioned. A nest, a template and light from below are enough to check during machine setup.

An RFID ticket, of the kind used in transport or hotels, looks like a piece of printed paper. But inside it contains an inlay: a chip and its antenna, laminated between two layers.

As long as the inlay stays in place, nobody thinks about it. The problem appears when it does not.

The risk you cannot see

If the inlay shifts relative to the ticket during manufacturing, nothing shows on the outside. The printing is right, the cut is right, the ticket looks perfect.

But a shift can leave the antenna exposed to a later cut. When the vending machine cuts and issues the ticket, the blade passes where it should not, cuts the antenna and the ticket stops working. And an error in the manufacturing machine itself can damage the inlay without anyone noticing.

None of that is visible during machine setup. The external appearance is not enough to know whether the internal assembly is where it should be. Without a strong light underneath, there is no way to see where the antenna has ended up.

The idea: light from below

Paper is opaque under normal lighting, but not when lit from behind. If the ticket is illuminated from below, the inlay appears as a shadow: you can see the antenna, the chip and where they sit relative to the edges.

That alone is nothing new. What makes it useful in production is something else: comparing that shadow against a reliable reference, quickly and repeatably, during setup and checks.

The fixture

The backlit fixture brings three things together in one body:

  • A fixed nest where the ticket is placed. Always in the same position.
  • A hinged lid with the template. When lowered, its locating points align the template with the ticket and hold it in place. There is no need to move a sheet by hand until the edges match.
  • Lighting from below that makes the interior visible.

The template marks the intended positions of the antenna and chip, along with other product references such as printing or logos. This means a single check shows whether both the inside and outside are where they should be.

After die cutting, units are checked one by one: open the lid, remove the sample, insert the next. The reference does not move.

The details that make it practical

A fixture like this is used beside the machine, not in a laboratory. That is why things beyond optics matter:

  • It is self-contained. A battery of around 3,000 mAh, with approximately four hours of runtime depending on use, and USB charging. No cables across the workstation.
  • The light is powerful and adjustable. A COB LED of around 2,000 lumens, with four brightness levels raised and lowered using two buttons. Different papers transmit light differently, and different inlays are not equally visible at the same power.
  • Battery status is visible on an LED bar, so the light does not go out halfway through a setup.
  • The light is switched on using the controls, independently of the lid. The operator decides when it is needed.

What the light checks, and what it does not

One point needs to be clear: backlighting checks position, not function.

The light shows whether the antenna and chip are where they should be. It does not tell you whether the chip responds, whether the antenna is correctly connected or whether the inlay works. That is a separate electronic check, using a reader.

The two complement each other. Position is checked during setup, to correct the machine before production. Function is checked through its own control. Confusing them would mean approving a ticket that has only been looked at.

That is why the next step has already been designed, although it has not yet been manufactured: an interchangeable base with a small reader antenna. The fixture sits on it, it reads the inlay and gives an audible indication of whether it responds. This would allow one check to show position with the light and confirm function through the reading.

The takeaway

If you manufacture or convert products with hidden elements — inlays, antennas, reinforcements, inserts:

  1. What cannot be seen can shift too. And it is often what matters most.
  2. Light from behind makes much of what the material hides visible.
  3. But light alone is not enough: you need a reference that is always positioned the same way.
  4. Put the internal and external features on the same template, to check them all at once.
  5. Make it practical at the workstation: self-contained, adjustable, quick to open and close.
  6. And do not confuse position with function. They are two different checks.

At 7Axis Industrial, we design inspection fixtures for what can be seen and what cannot: guided positioning, reference templates and lighting adapted to each product.

View the complete project → Quality, inspection and poka-yoke →

Keep reading

All articles

Production decisions

Before adding machine vision, try a template

The first proposal for checking chip position in cards was a camera on every machine. The customer wanted something simpler. A nest, a lid and a transparent template solved the problem and opened the door to a whole family of fixtures.

Read the article

Production decisions

Check what does the checking too

An inspection fixture is a reference. If that reference moves, wears out or gets confused with another, everything checked against it becomes questionable. Three design decisions to keep the fixture telling the truth.

Read the article

Production decisions

The same reference at both ends

When the manufacturer and the recipient check against different criteria, every batch becomes an argument. An identical inspection fixture at both ends turns that argument into a comparison.

Read the article

Workshop practice

Draw the tolerance, not the nominal dimension

A checking template that marks where something should be forces the operator to decide how much error is too much. One that marks the permitted limits leaves just one question: inside or outside? What I learned from making dozens of card templates.

Read the article

Your next step

Facing a similar problem?

Tell me what is happening, what you need to achieve and what you have tried. We can then look at a specific intervention.